motors-teco TECO Motors

Single Phase TEFC

Totally Enclosed Fan Cooled

teco-1PH

HP.33 hp through 10 hp Speed1800 RPM Voltage 115/230V, 230V Frequency 60 Hz.

Features

  • High-Torque design for tough applications such as farm-duty
  • 1.15 SF through 10 hp
  • Oversized ball bearing
  • Manual reset overload protector installed with rubber boots/gasket
  • Rugged cast-iron frame and endbells 143T through 215T
  • Oversized and gasketed conduit box
  • Non-hygroscopic insulation system
  • Zn-Cd plated hardware
  • Dynamically balanced pressure die-cast aluminum rotor
  • Ground terminals
  • Condensation drain holes

Cast Iron ODP NEMA Premium

Open Drip Proof

teco-cast-iron

HP1 hp through 400 hp Speed 3600, 1800, 1200 RPM Voltage 230/460V (usable on 208V), 460V, 575V Frequency 60 Hz.

Features

  • HPE™ – High Pulse Endurance Wire
  • Premium efficiency and high power factor
  • Corrosion resistant hardware
  • Lead lugs on 143T to 449T frame
  • Neoprene lead separator
  • F-1 and F-2 mounting interchangeability
  • C-Flange, D-Flange and P-Base kits available for 254T to 449T frame
  • Fully tested and documented per IEEE 112, Method B and NEMA MG-1
  • Class B temperature rise
  • CE Mark on Nameplate
  • 1.15 service factor
  • Suitable for 208V operation from 1HP to 125HP
  • Suitable for wye-delta starting from 7.5HP to 400HP (12 leads for 7.5HP to 125HP, 6 leads for 150HP to 400HP)
  • Suitable for Inverter Duty per NEMA MG1-31.4.4.2 – speed ranges 20:1 variable torque, 5:1 constant torque
  • 6 Leads only on 575 Volt

GLOBAL-MAX Standard Efficiency ODP

Open Drip Proof

teco-global

HP300 hp through 500 hp Speed 3600, 1800, 1200 RPM Voltage 460V Frequency 60 Hz.

Features

  • Design Standard: NEMA MG-1; MG-13; NEMA Design B, continuous duty
  • Conversion Kits: C-Face, D-Flange
  • Class F insulation with Class B temperature rise
  • Cast-iron frame
  • Cast-iron end bells and conduit boxes for all ratings
  • Copper windings
  • Oversized ball/roller bearings
  • 40°C Ambient, 1.15 SF
  • Full Voltage or Wye-Delta Starting
  • Three Year Warranty

Oil Well Pump

Open Drip Proof

teco-oil-well

HP5 hp through 150 hp Speed 1200 RPM Voltage 230V, 460V, 796V Frequency 60 Hz.

Features

  • NEMA Design D, 5-8% slip
  • Cast-Iron Frame, End Brackets and Oversized Conduit Box
  • Fully guarded with Rodent Screen
  • Oversized Bearings selected for Belt-drive application
  • Grounding Terminals on Frames and Inside Conduit Box
  • Thermal Protectors embedded in Winding in each Phase
  • Stainless Steel Nameplate
  • F2 Mounting

Rolled Steel ODP NEMA Premium Efficiency

Open Drip Proof

teco-rolled-steel

HP.33 hp through 40 hp Speed 3600, 1800, 1200 RPM Voltage 230/ 460V (Usable on 200V and 208V) Frequency 60Hz

Features

  • AC, 3 phase, 60 Hz, 208-230/ 460V, 1.15 SF
  • NEMA Design B performance
  • UL recognized Class F non-hygroscopic insulation system
  • Class B temperature rise
  • Multiple mountings for 56 and 140T; dual mountings for frame 180T~280T
  • Interchangeable F1 and F2 mounting for frame 180T~280T
  • Bi-directional rotation
  • 90 degree rotatable oversized and gasketed conduit box
  • Stainless steel nameplate
  • Accepts C-face conversion kit
  • Three year warranty
  • Suitable for Inverter Duty per NEMA MG1-31.4.4.2 – speed ranges 20:1 variable torque, 5:1 constant torque

3-Phase Fractional HP

Totally Enclosed Fan Cooled

teco-3PH

HP.33 hp through 2 hp Speed 3600, 1800, 1200 RPM Voltage 230/460V, (usable on 208V) Frequency 60 Hz.

Features

  • Heavy Gauge Steel Frame With Condensation Drain Holes
  • Ribbed Die-Cast Aluminum Endbells With Machined SteelBearing Seat and Shaft Slinger
  • Large Size Double-Gasketed 90 Degree Rotatable Conduit Box
  • Oversized Vacuum De-Gassed Ball Bearing
  • High-Grade Insulated Electro-magnetic Steel Stator With Polyester Enameled Copper Wire
  • Cast-Iron C-Face Kit For Rigid Base Mount Motors
  • Cd-Zn plated Corrosive-Resistant Hardware

Closed Coupled Pump JP/JM Epact

Totally Enclosed Fan Cooled

teco-CC-pump

HP.75 hp through 50 hp Speed 3600, 1800, 1200 RPM Voltage230/460V (usable on 208V) Frequency 60 Hz.

Features

  • Class F insulation with Class B temperature rise
  • Cast iron frame and endbells
  • Copper windings
  • Oversized ball bearings
  • Conversion Kits CHEM-DUTY Kits
  • Continuous SF 1.15 or 1.0

MAX-E1® NEMA Premium Efficiency - Footed & Round Body C-Face

Totally Enclosed Fan Cooled

teco-max-e1

HP3/4 hp through 800 hp Speed3600, 1800, 1200, 900 Voltage 230/460V (usable on 208V), 460V, 575V Frequency 60 Hz.

Features

  • Inverter Duty Magnet Wire
  • Non-hygroscopic, Class F insulation system
  • High-grade, electro-magnetic steel laminations for low core loss and high efficiency
  • All cast-iron construction including IP55 frame, end brackets, fan cover and conduit box for rigidity and excellent corrosion resistance
  • Reinforced end turn lacing
  • Neoprene lead separator
  • High performance bearings of degassed steel
  • 90° rotatable oversized cast iron conduit box for easy connection
  • Corrosion-resistant non-sparking external fan
  • Dynamically balanced pressure die-cast aluminum rotor
  • Phenolic rust-proof base coat
  • Round-body motors feature cast-iron drip cover
  • Zn-Cd coated hardware
  • CSA Certified for Class 1, Division II, Groups B, C and D, with Temperature Code T3C
  • CSA and UL approved for Inverter Duty per NEMA MG1 Part 31, with speed range of 20:1 variable torque and 10:1 constant torque

MAX-E2® NEMA Premium Efficiency - Inverter, Severe Duty, TEFC

Totally Enclosed Fan Cooled

teco-max-e2

HP1 hp through 300 hp Speed 3600, 1800, 1200 RPM Voltage 460V, 575V Frequency 60 Hz.

Electrical Features

  • Designed to meet NEMA MG-1, MG-13
  • Stock available in 460V and 575V; other voltages available upon request
  • Premium efficiency; meets or exceeds NEMA PREMIUM, EPACT ‘ 92 and Canadian Federal Efficiency Levels defined in CSA C390-93; Full load efficiency of all ratings is certified under the EEV Program of the CSA
  • Motors are NEMA Design “B” and “C” Torque
  • UL recognized Class F non-hygroscopic insulation system with HPE™ (High Pulse Endurance) index, heavy heat resistance enameled copper wire ensures longer winding life and reliability
  • CSA certified for Class1, Division 2, Groups B, C and D with Temperature Code T3C
  • Class B temperature rise, 80°C rise by resistance method at 1.0 SF; 90°C rise at 1.15 SF
  • 3 Leads solderless lug terminals

Mechanical Features

  • Bearing temperature rise is below 45°C for all 4P and 6P ratings; 50°C for all 2P motors
  • Sound power levels are below 85 dBA providing quiet operation
  • Full cast iron construction: frame, brackets, fan cover and conduit box with IP55 rated protection
  • Frame provided with two threaded drain holes with drain plugs and a drilled and tapped hole for a ground lug
  • Corrosion-resistant cast iron conduit box has twice the volume required by NEMA; Conduit box is fully gasketed with NPT threaded conduit entry
  • Regreaseable bearing construction with inner bearing caps prevent bearing contamination
  • Non-sparking plastic or bronze fan
  • All internal rotor, stator and shaft surfaces are cleaned and coated with moisture resistant varnish; Exterior is painted with zinc-chromate epoxy base with a blue finish
  • Stainless steel hardware and nameplate
  • Vibration will not exceed 0.08 inches per second
  • Motors can be re-rated for 415, 400 and 380 volt 50 HZ
  • CSA and UL approved for Inverter Duty per NEMA MG1 Part 31, with speed range of 20:1 variable torque and 10:1 constant torque

MAX-E2/841™ NEMA Premium Efficiency - Inverter, Severe Duty, TEFC

Totally Enclosed Fan Cooled

teco-max-e2-841

HP1 hp through 300 hp Speed 3600, 1800, 1200 RPM Voltage 460V, 575V Frequency 60 Hz.

Electrical Features

  • Designed to meet NEMA MG-1, MG-13 and IEEE 841
  • Stock available in 460V and 575V; other voltages available upon request
  • Premium efficiency; meets or exceeds the requirements of EPACT ’92 and Canadian Federal Efficiency Levels defined in CSA C390-93; Full load efficiency of all ratings is certified under the EEV Program of the CSA
  • UL recognized Class F non-hygroscopic insulation system with HPE™ (High Pulse Endurance) index, heavy heat resistance enameled copper wire insures longer winding life and reliability
  • CSA certified for Class 1, Division II, Group B, C and D with Temperature Code T3C
  • Class B temperature rise, 80°C rise by resistance method at 1.0 S.F.; 90°C rise at 1.15 SF
  • 3 Leads solderless lug terminals
  • Meets GM 7E-TA specifications

Mechanical Features

  • Bearing temperature rise is below 45°C for all 4P and 6P ratings; 50°C for all 2P motors
  • Sound power levels are below 85 dBA providing quiet operation
  • Full cast iron construction: frame, brackets, fan cover and conduit box with IP55 rated protection
  • Frame provided with two threaded drain holes with drain plugs and a drilled and tapped hole for a ground lug
  • Corrosion-resistant, cast iron conduit box has twice the volume required by NEMA. The conduit box is fully gasketed with NPT threaded conduit entry
  • Regreaseable bearing construction with inner bearing caps prevent bearing contamination
  • Non-sparking plastic or bronze fan
  • All internal rotor, stator and shaft surfaces are cleaned and coated with moisture resistant varnish; Exterior is painted with zinc-chromate epoxy base with a blue finish
  • Stainless steel hardware and nameplate
  • Vibration will not exceed 0.08 inches per second
  • Motors can be re-rated for 415, 400 and 380 volts at 50 HZ
  • CSA and UL approved for Inverter Duty per NEMA MG1 Part 31, with speed range of 20:1 variable torque and 10:1 constant torque

MAX-E2/841™ NEMA Premium Efficiency - Footed & Round Body C-Face

Totally Enclosed Fan Cooled

HP1 hp through 100 hp Speed 3600, 1800, 1200 RPM Voltage 460V Frequency 60 Hz.

Electrical Features

  • Designed to meet NEMA MG-1, MG-13 and IEEE 841
  • Stock available in 460V and 575V; other voltages available upon request
  • Premium efficiency; meets or exceeds the requirements of EPACT ’92 and Canadian Federal Efficiency Levels defined in CSA C390-93; Full load efficiency of all ratings is certified under the EEV Program of the CSA
  • UL recognized Class F non-hygroscopic insulation system with HPE™ (High Pulse Endurance) index, heavy heat resistance enameled copper wire insures longer winding life and reliability
  • CSA certified for Class 1, Division II, Group B, C and D with Temperature Code T3C
  • Class B temperature rise, 80°C rise by resistance method at 1.0 S.F.; 90°C rise at 1.15 SF
  • 3 Leads solderless lug terminal
  • Meets GM 7E-TA specifications

Mechanical Features

  • Bearing temperature rise is below 45°C for all 4P and 6P ratings; 50°C for all 2P motors
  • Sound power levels are below 85 dBA providing quiet operation
  • Full cast iron construction: frame, brackets, fan cover and conduit box with IP55 rated protection
  • Frame provided with two threaded drain holes with drain plugs and a drilled and tapped hole for a ground lug
  • Corrosion-resistant, cast iron conduit box has twice the volume required by NEMA. The conduit box is fully gasketed with NPT threaded conduit entry
  • Regreaseable bearing construction with inner bearing caps prevent bearing contamination
  • Non-sparking plastic or bronze fan
  • All internal rotor, stator and shaft surfaces are cleaned and coated with moisture resistant varnish; Exterior is painted with zinc-chromate epoxy base with a blue finish
  • Stainless steel hardware and nameplate
  • Vibration will not exceed 0.08 inches per second
  • Footed and Round Body C-Face Mounting
  • Motors can be re-rated for 415, 400 and 380 volts at 50 HZ
  • CSA and UL approved for Inverter Duty per NEMA MG1 Part 31, with speed range of 20:1 variable torque and 10:1 constant torque

Motor

Ready to get started?

Contact us with your information. Our team will provide you with a customized quote.

Contact Us

NEMA EASA IEEE